This item has been shown 34445 times.
TME® REAL ALUMINUM SENSING FOIL FOR 1/4" OPEN REEL TAPE 26 FOOT ROLL
"Finally, sensing foil that actually works! I love this stuff!" -AS, Henderson Nevada
Product Description:
- Real Professional Studio Grade™ Aluminum Sensing Foil (Not Inferior "Aluminized Painted Plastic")
- 7/32" x 26' long on 3" Easy Handle plastic core (Also available on 54 foot rolls)
- Important: Cut to the length you need for your deck's sensitivity and operating speed
- Custom made in Europe to exacting TME specifications in an ISO 9001 Certified Facility
- Highly conductive real soft aluminum made for the purpose. Even the adhesive is conductive!
- Less than 0.005 Ohms Resistance per ASTM
- Large 3" Professional Core for Easier Handling and Far Less curling than those teenie rolls
- Long Lasting and Clean Adhesion will not OOZE in time like other products
- Also available as pre-cut tabs on a EZ to peel off rolls of 30, 60, 90 and 120 tabs.
TME Professional open reel deck
sensing foil is custom made in USA specifically for open reel tape sensing to TME specifications. It is real, highly conductive soft aluminum foil with a non-oozing aerospace
adhesive. Almost every other foil we see being sold as open reel sensing foil is "vapor
evaporated aluminized plastic" hobby tape which is plastic coated with aluminized paint to make it shiny. That tape is fine for arts and crafts, but they do not have the conductive qualities of real foil, and from our customer's experiences, will eventually wear out, may not work at all on some decks, and will ooze adhesive, contaminating your deck and precious tapes. That hobby tape is not meant for this application! It's not worth the risk to potentially damage thousands of dollars worth of tapes over an inexpensive item. Also, those hobby tapes generally are .25" wide or slightly more which will make it nearly impossible to add to sensing to your tapes without having some of it overlap the edge of the tape which will goo up your heads and guides which is definitely not recommended. Sensing foil is used on
any audio tape deck using foil for auto reverse and/or auto stop sensing
like some TEAC models. Note: No, it will not *turn* your deck into a reversing or
auto-stop deck if it's not designed to do those functions! (We had to
say that.) TME ACFOIL-26 comes 26 feet on a roll with a 3" diameter plastic core. The foil has backing release paper which you remove the foil from before you adhere your new tab to the tape. We chose to use the backing
release paper rather than having the foil stick to itself on the roll to
keep the foil surface as clean as possible. This also allows for neat, angled cuts or butt cuts with a splicing block before application. Each roll should have
enough foil for one end of around 260 tapes or more. To use: Cut about 1" or so
(depending on your deck's sensitivity), center and apply the foil to the surface of the
tape where your sensors are. Smooth down with a cotton tipped applicator. Sensing foil is almost always applied to the side of
the tape away from the heads and NOT the oxide side. Check your manual. There should be a
slight gap between the edge of the foil and the edge of the tape if
centered properly but it doesn't have to be perfectly centered. Specifications:
Foil Thickness: 1.5 Mil
Total Thickness: 2.10 Mil
Tensile Strength: 14 Lb/In
Electrical Resistance: <0.005 Ohms per Mil Spec
US Recording Media, LLC is the leading source for
professional post
production supplies in the country servicing the best studios and the
leading government, university, and private archives as well as the home
recordist wanting the very best quality. TME®, Studio Grade™, VNC-4™,
VNC-8™, CL-100™, RC-5™, VCFB™, Studio Grade™ and Feedpack™ are trademarks of US Recording
Media, LCC. All Rights Reserved.